Discussions

• Mecway mesh - extraneous surface lines at bottom of drilled hole

  198 views 6 comments 0 points Most recent by dculp February 2025
• Error box when attempting to post

  76 views 1 comment 0 points Most recent by Victor February 2025
• gmsh - How to change the 2D quad element size?

  634 views 2 comments 0 points Most recent by dculp February 2023
• Surface mesh with poor element (nearly colinear nodes)

  189 views 5 comments 0 points Most recent by dculp February 2023
• Model solid cylinder with brick (hexahedron) elements rather than tet elements?

  370 views 10 comments 0 points Most recent by disla February 2023
• How to set up spring-mass modal vibration model?

  440 views 26 comments 0 points Most recent by Victor November 2022
• Possible to prevent stress calcs in modal analysis?

  240 views 13 comments 0 points Most recent by prop_design October 2022
• Contour plot -- Greyscale gradient seems wrong

  150 views 6 comments 0 points Most recent by disla October 2022
• gmsh from Mecway's GUI - any way to specify minimum number elements per edge?

  183 views 3 comments 0 points Most recent by afro_samurai September 2022
• 3D meshing -- How is "Maximum element size" determined?

  756 views 7 comments 0 points Most recent by disla October 2022
• "Save after solve" - can model automatically refer to itself?

  109 views 4 comments 0 points Most recent by JohnM August 2022
• Change number of decimals in legend?

  47 views 1 comment 0 points Most recent by Victor August 2022
• Running Mecway solve from a Windows batch file

  91 views 6 comments 0 points Most recent by dculp August 2022
• Where are the CCX solver "Details ..." saved?

  106 views 5 comments 0 points Most recent by kennethfugate August 2022
• Any way to invert legend colors?

  1.7K views 12 comments 0 points Most recent by GFB May 2025
• Assigned custom colors for contour plot are not correctly displayed

  280 views 14 comments 0 points Most recent by dculp October 2022
• Static pull test - odd/incorrect results depending on mesh density and boundary conditions

  486 views 19 comments 0 points Most recent by Victor August 2022
• Using frictionless supports with a bonded contact -- where not allowed?

  232 views 1 comment 0 points Most recent by Victor June 2022
• Any way to select all surfaces?

  137 views 4 comments 0 points Most recent by disla January 2022
• Any way to disable a part (analyze without removing the part)?

  146 views 4 comments 0 points Most recent by disla January 2022
• How to export selected nodal results to a spreadsheet?

  212 views 4 comments 0 points Most recent by Sergio May 2021
• Frequency response analysis - manually adjusting Dynamic Response

  172 views 1 comment 0 points Most recent by Victor May 2021
• Modal analysis -- specify frequency range?

  402 views 5 comments 0 points Most recent by Victor May 2021
• Imported step file -- meshing fails with Netgen (default) but OK with Netgen 6

  655 views 17 comments 0 points Most recent by Hengre May 2021
• How to look inside a model (slice)?

  245 views 9 comments 0 points Most recent by dculp May 2021
• Static analysis - "ERROR in cascade" with CCX solver (OK with internal solver)

  660 views 5 comments 0 points Most recent by dculp April 2021
• How to set/save view for 3D model (rotate about coordinate axes)?

  437 views 5 comments 0 points Most recent by JohnM April 2021
• Best way to detect incorrect bonded contact (gaps)?

  335 views 8 comments 0 points Most recent by Victor April 2021
• Better view of geometry edges for imported step file?

  63 views 0 comments 0 points Started by dculp April 2021
• Problem with transforms in DisplacementCylindrical.liml

  134 views 3 comments 0 points Most recent by prop_design April 2021
More Discussions